Product Introduction
Category:
Through-beam edge measurement sensor
• One-to-two
• Long-distance detection, up to 300mm
• IP67 protection rating
• High speed
- Product Details
- Specification Parameters
- External dimensions
-
I. Small Size & Ultra-Thin Design
II. Easily Adjust the Optical Axis
Before alignment: Lights are flashing. After alignment: Lights remain constantly on. 
III. Operation Interface
- Measurement status
Operation panel 
Easy to operate, with Chinese-English switching. - Channel Selection
Press the △ button to configure Channel 2.
Press the ▽ button to configure Channel 1.
Press the ❍ key to return to the previous menu.
Application scenarios 
Thin-Film Winding Control (Edge-Tracking Measurement) Thin-film bending control (edge measurement) Measure the outer diameter of the ampoule. 
Lithium-ion battery edge correction (edge measurement, positioning) Roller deviation detection Cable Extrusion Outer Diameter Measurement 
Slot for wafer inspection LCD circuit board positioning Leadframe Edge Control 
Film Winding Control Check the height of the spring. Measure the outer diameter of the pipe. 
Detecting the tilt of bottle caps Measure the outer diameter of the capacitor. Measure the outer diameter of the ampoule. -
Sensor Model Transmitting head: JGS-10T; Receiving head: JGS-10R Measurement range Edge mode: ±5mm, Width mode: 10mm Induction head installation distance Max.300mm Laser wavelength Red semiconductor laser 660nm Maximum laser output power 390uw Laser class CLASS1 (IEC/JIS) Spot size 3x14mm Linear accuracy When the sensing head is installed at a distance of 100 mm: +0.4% F.S. (±40 µm) Repeatability ±5 μm Sampling period 500 μs, 1000 μs, 2000 μs, 4000 μs Temperature drift ±0.02%F.S./℃ Indicator lights *3 Transmitter power indicator: green; Receiver power indicator: green; Alarm indicator: red Communication method RS-485 Power supply voltage DC 12~24V ±10% Current consumption Transmitter: Below 20mA (at DC12V)
Receiver: Below 150mA (at DC12V)
Connection type Connector: MB 4-pin connector, with a 300mm cable. Protection circuit Reverse connection protection Protection level IP67 Operating temperature/humidity - 10~+50℃ / 35~85% RH (no condensation, no frost) Storage environment temperature/humidity - 20~ +60℃ / 35~85% RH (no condensation, no frost) Ambient Illuminance Sunlight: below 10,000 lx; incandescent lamp: below 3,000 lx Anti-vibration 10–55 Hz, double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions Impact-resistant Approximately 50G (500 m/s²), 3 times in each of the X, Y, and Z directions. Quality Transmitter, receiver: 30g each (including a 300mm power cable) Material Housing: Die-cast aluminum; Transmitting and receiving lens: Glass Controller Model JGS-K200 Installation method DIN Rail Mounting Setup Sensor Number of connected devices Max. 2 units Communication method RS-485 Display Measured value. Set value Dot matrix display, 128 x 64 pixels, Chinese/English optional. Indicator light Power indicator light: Red Output indicator: Orange Communication indicator light: Green I/0 Digital output 3-channel output NPN Max. 100mA / DC 24V Residual voltage below 1.8V Rated value Power supply voltage DC 12~24V ±10% Current consumption Less than 120mA (at 12V) *1 Environmental resistance Protection circuit Reverse polarity protection and overcurrent protection functions Protection level IEC rating IP50 Operating temperature/humidity - 20~+50℃ / 35~85% RH (no condensation, no frost) Storage environment temperature/humidity -20~ +60℃ / 35~85% RH (no condensation, no frost) Anti-vibration 10–55 Hz, double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions Impact-resistant 500 m/s² (approximately 50 G), 3 times in each of the X, Y, and Z directions Material PC Weight 170g Analog output 0–5V Measurable transparent objects √ Accessory (cable) model OP-2001 -
Model: JGS-10T/JGS-10R
Accessory (Y-shaped cable) Model: OP-2001
Model: JGS-K100/JGS-K200
Keywords:
Sensor
Measurement sensor
Measuring instrument
Visual system
Communication
Recommended Products
If you have any questions or would like to learn more details, please contact us!
Address: No. 36, Moganshan Road, Beilun District, Ningbo City, Zhejiang Province
Phone:+86-574-82822433 / (400)8679286
Fax:+86-574-88137049
Email:office@ejanpos.com